WW Collet Sets

SKU: N/A Categories: ,

This product is currently out of stock and unavailable.

Product Description

Collets provide a quick, easy method of mounting cylindrical parts or bar stock in the lathe with a great deal of centering accuracy. Each collet is actually a small, precision 3-jaw chuck that fits into a special tapered adapter in the headstock. A drawbar that passes through the headstock and threads into the backside of the collet is used to draw the collet up into the tapered adapter. The adapter causes the jaws of the collet to close down, gripping the part to be machined. Typically, collets provide a very accurate part mounting system, but each size collet can accommodate only a small range of diameters of approximately ±.001″ (.02mm).

WW collets differ from milling collets in that they have a hole all the way through the collet and drawbar. The maximum diameter stock that can pass entirely through the collet is 3/16″ or 4.5mm. The WW collets that are larger than this diameter are sometimes referred to as “pot” chucks.

The Sherline WW collet set includes a WW style collet taper adapter, a drawbar, and a set of five WW collets. These collets are manufactured by Sherline and are built to standard WW specifications; however, we have come across collets that are called WW and will not fit our drawbar and adapter. Be sure to check WW collets made by other manufacturers to be sure they fit our adapter before you purchase them. Sherline manufactures a slightly larger .315″ adapter and drawbar set that will accommodate some of these other brands.

Collet Accuracy

These collets have a maximum runout of .002″ or less. If the WW collet adapter is trued in as suggested in the instructions, it will run dead true. This will allow the collet runout to be at its best. Collet sizes above 3/16″ (4.5mm), considered pot chucks, are not bored through. They are only bored .260″ deep and depending on your setup and length of the part, you may experience greater runout further away from the front of the collet.

5-piece collet set includes:

  • WW Collet Adapter*
  • Drawbar & 3/8″ Knockout Bar
  • Set of 5 Collets:
    Inch set: 1/16″, 1/8″, 3/16″, 1/4″, and 5/16″
    Metric set: 2.0 mm, 3.0 mm, 4.0 mm, 5.0 mm, and 6.0 mm

*NOTE: Our WW collet adapter does not have a keyway pin for the collets. Our customers have been using our WW collets on our lathes without a key pin for over forty years without any problems.

Other Collet Sets

Sherline also offers sets that include a wider selection of collets. It includes 17-inch size collets from 1/16 to 5/16″, while the metric set includes 14 metric collets from 1.5 mm to 8.0 mm. These sets come in an oak box with a divider that has extra holes for more collets should you add them later. It also includes a drawbar, a collet adapter, knockout bar, two collet pot chucks, and a collet blank.

The largest set we offer includes 78 collets from 0.3 mm to 8.0 mm by 0.1 mm increments. This comes in an oak box with 96 holes in case you add some inch sizes but does not include the adapter, drawbar or other accessory items in the sets described above.

warning-symbol
The improper use of machine tools and their accessories can result in serious injury. Before using this tool, thoroughly read the instructions and make sure you understand its proper and safe use.

safety-glasses-symbol

Always wear safety glasses when operating machine tools.

Download PDF 1160 Instructions

Instructions PDF Download

Download PDF Sherline WW Collet Comparison

Instructions PDF Download

Part No. Description Quantity
Common Parts
11570 Knock Out Bar 1
11580 WW Collet Adapter 1
11590 Collet Drawbar 1
1160 Collets (Inch)
116004 1/16″ (.0625) WW Collet 1
116008 1/8″ (.1250) WW Collet 1
116012 3/16″ (.1875) WW Collet 1
116016 1/4″ (.2500) WW Collet 1
116020 5/16″ (.3125) WW Collet 1
1178 Collets (Metric)
117820 2.0mm (.0787) WW Collet 1
117830 3.0mm (.1181) WW Collet 1
117840 4.0mm (.1575) WW Collet 1
117850 5.0mm (.1969) WW Collet 1
117860 6.0mm (.2362) WW Collet 1