Single-Axis Slide with Programmable CNC Contoller

Single-axis CNC programmable machine slides available with table lengths of 8″, 13″, or 18″.
Select your table size and unit type for pricing.

SKU: N/A Tag:
  • *Preferred unit of measurement for laser engraved portions
    Please note that our ball screws only come in a metric pitch
    Reset options

Product Description

About the Sherline Industrial linear machine slide with programmable CNC controller

Sherline offers single-axis controllers to drive the stepper motor on any individual axis of the lathe or mill. No separate computers or drivers are needed. The keypad/control unit has its own computer chip built-in. It is all ready for you to use the keypad to drive the stepper motor directly or to enter simple program commands to do sequenced operations. No knowledge of G-code is required. Parameters that can be entered are direction, distance to travel, feed rate, and whether or not the program pauses to wait for another command or proceeds to the next step. Up to 40 programmed steps of four parameters each can be entered into either of two separate user-settable programs. Controllers can be interconnected with a cable to signal each other to act in sequence. They can also be connected to other CNC system controllers to communicate with “sense” and “acknowledge” signals so that they perform their preprogrammed functions at the proper time during a CNC program sequence.

The stepper motor mounts feature dual ball bearings with a preload nut to eliminate endplay. A dampened coupling connects the 1/4″ diameter shaft of the stepper motor to the leadscrew. The use of a dual-shaft stepper motor allows manual cranking by means of the supplied handwheel as an alternative to computer-controlled movement. The controller uses micro-stepping to provide accurate, smooth travel.

Mounting Provisions

FROM THE BOTTOM—Four 1/4-20 holes are provided in the base’s bottom on 2-inch centers for mounting.

FROM THE TOP—If access is not available from the bottom, the slide can be mounted from the top using the four angle clamps provided. They slide into the groove around the perimeter of the base, and holes are drilled in the mounting surface and tapped to accept the 10-32 socket head cap screws provided. Use all four clamps for the most secure mount.

Items included with the Linear Machine Slide with Programmable Controller:

  • Single-axis slide, available with 8″, 13″, or 18″ table
  • Linear Controller w/Keypad
  • Power Supply
  • #23 Frame Size Stepper Motor
  • 1-5/8″ Handwheel graduated in .001″ increments on inch slides and in .01 mm increments on metric slides.
  • Cables
  • Complete instructions

NOTE: The power supply included with this indexer (linear controller) is intended to operate only on 115/120 VAC, 60 Hz (38 W) current. For countries operating on 100, 220, or 240VAC and/or 50Hz a transformer will be required. As an alternative, this power supply outputs 24VDC, 1 Amp (1000 mA). If you can purchase an appropriate power supply that operates on local current and outputs 24VDC, 1A current, it could be used to power the unit instead of the one supplied. Sherline Products does not provide a 220V power supply or transformer.

Weight Capacity

Our slides’ weight capacity is about 10 lbs. depending on where the weight is located and how long the table is. On an 18″ table, you should not go more than 10 lbs. of weight at the end of the table (there is a leverage factor). If the weight is more centrally located (closer to the base), you can exceed the 10 lbs. limit.

Duty Cycle

Under heavy constant use, the dovetail area of the slide will start to show some wear on the anodize after one year (2080 hours). They are still fully functional at this point, but the anodized coating will begin to wear thin. The dovetail and the screw will last longer if you keep them lubricated with light oil*.

*NOTE: Do not use WD-40 as a lubricant on these slides. WD-40 will remove the anodized coating from these parts!

warning-symbol

The improper use of machine tools and their accessories can result in serious injury. Before using this tool, thoroughly read the instructions and make sure you understand its proper and safe use.

safety-glasses-symbol

Always wear safety glasses when operating machine tools.

Download PDF 6550 Instructions

Instructions PDF Download

Download PDF Inch 8800 Instructions

Instructions PDF Download

Download PDF Metric 8810 Instructions

Instructions PDF Download

Linear Controller Specs
Power Supply Input: 115 VAC 50/60 Hz, Output: 24V, 1 Watt
Stepper Motor 100 oz-in, 2 Amp, #23 Frame size, 400 steps per revolution
Speed 1″/min. to 25 in/min (programmable)
Distance from 0.0005″ to 9.9995″ in steps of 0.0005″
Backlash Compensation Programmable
Table Specs
6550 (6551) 8″ table 6555 (6556) 13″ table 6550-18 (6551-18) 18″ table
Table size 2.75″ x 8″ (70 mm x 203 mm) 2.75″ x 13″ (70 mm x 330 mm) 2.75″ x 18″ (70 mm x 458 mm)
Table height 2″ (51 mm) 2″ (51 mm) 2″ (51 mm)
Table travel 4″ (102 mm) 8″ (203 mm) 14″ (356 mm)
Hold-down provision 2 T-slots 2 T-slots 2 T-slots
Mounting provision 4 holes 1/4-20 in the bottom of the base plus slot for angle clamps 4 holes 1/4-20 in the bottom of the base plus slot for angle clamps 4 holes 1/4-20 in the bottom of the base plus slot for angle clamps
Handwheel 1-5/8″ laser engraved aluminum with two pre-loaded ball bearings 1-5/8″ laser engraved aluminum with two pre-loaded ball bearings 1-5/8″ laser engraved aluminum with two pre-loaded ball bearings
Industrial Slide Tables
Part No. Description Quantity
12050 8-32 x 3/8″ Socket Head Cap Screw 4
30561 10-32 T-Nut 4
35580 Angle Clamp 4
40080 (41040 Metric) 1-5/8″ Handwheel 1
40520 10-32 x 3/16″ Cup Point Set Screw 3
40690 10-32 x 3/4″ Socket Head Cap Screw 4
40740 10-32 x 7/8″ Socket Head Cap Screw 1
40820 Gib Lock 1
40890 (41890 Metric) Leadscrew Nut 1
40980 Gib 1
44210 (44220 Metric) 8″ Leadscrew (6554/6554M) 1
50171 (51171 Metric) 13″ Leadscrew (6559/6559M) 1
50173 (51773 Metric) 18″ Leadscrew (6554-18/6554M-18) 1
50150 Backlash Lock Star Gear 1
50210 Button Head Socket Screw 1
50130 (51130 Metric) Backlash Lock Nut 1
65501 Base 1
65502 Table Lock 1
67036 8″ Slide Table (6554/6554M) 1
67050 13″ Slide Table (6559/6559M) 1
54182 18″ Slide Table (6554-18/6554M-18) 1
67101 CNC Mount 1
671052 CNC Coupler 1
67106 (67108 Metric) Preload Nut 1
67111 8-32 x 7/8″ Socket Head Cap Screw 2
67115 5-40 x 1” Socket Head Cap Screw 1
67120 Ball Bearing W/ Flange 2
CNC Linear Controller
Part No. Description Quantity
67127 Stepper motor assembly 1
87041 120 VAC power supply (24 VDC, 1 amp output) 1
87250 Stepper motor-to-control box 6’ extension cable 1
87350 Single 5-pin mini-DIN limit switch cable or ½ of daisy-chain cable 1
88010 Linear controller/keypad unit complete 1

Click the P/Ns below to download a zipped version of the IGS 3D CAD file. You will need to extract the zip file before viewing the IGS file.
8″ 6554/6554M 3D IGS model
13″ 6559/6559M 3D IGS model
18″ 6554-18/6554M-18 3D IGS model
You need an IGS viewer to view .igs files. CLICK HERE to download a FREE IGS viewer.

Shipping

We do not charge a flat rate for shipping because of the variations in weight for our products. Instead, we charge you what the shipping company charges us. Our website uses a shipping calculator based on the daily rates for USPS and UPS based on the weight and destination of the shipment. You can also have us use your UPS/FedEx account number to charge your shipping. Just enter it in the appropriate box on the checkout page.

Domestic orders are shipped Monday – Friday. Expedited orders must be placed by 9 am PST to ship the same day.

Orders shipping ground have a processing time of 7 working days for domestic orders and 14 working days for international orders. CLICK HERE for more information on our shipping and order policies.

Returns

Most merchandise can be returned within 30 days of the purchase date. A refund will be issued to the original form of payment at the original selling price. View our complete return policy and/or start your return online here.